Manuscripts

Recent Papers

Research Paper

Design, analysis and manufacturing of semi automatic book binding machine

This semi-automatic book binding machine can be used to bind pages which is very important in libraries, govt. departments, offices, companies, lawyers, and book covers generally to maintain their books and records in good condition. This book binding machine is designed to performed operations semi-automatically. In term of the semi-automatic machine, it uses a different mechanism such as gripping mechanism, nut and bolt mechanism, folding mechanism, etc. This machine is designed and construct that can bind book which is in A4 size. It can minimize human energy consumption in order to bind books

Published by: Akshay Dharpale, Swapnil Dimble, Akshay Dalvi, Kiran Desai, V. M. Bansode

Author: Akshay Dharpale

Paper ID: V5I3-1672

Paper Status: published

Published: May 30, 2019

Full Details
Research Paper

Selection of phase change material based on AHP and TOPSIS method

Selection of PCM plays an important role in storing latent heat in a thermal energy storage system. PCM can be selected by different methods such as; AHP(Analytical Hierarchy Process), ENTROPY, FUZZY TOPSIS METHODS. This paper contains AHP and TOPSIS method calculation. AHP method is used to determine weight criteria while TOPSIS is used for obtaining the rank of criteria. A drawback to select an appropriate PCM used in domestic water heater system using triplex tube heat exchanger (TTHX) is coping up by desired methods. PCM liquidification and solidification under different mass flow rates are investigated. Internal and external fins are used to improve the heat transfer rate during charging and discharging of PCM.

Published by: Sahil Sunil Gharat, Suyog Vilas Gosavi, Krutika Dhondiram Mane, Sumedh Dinesh Gotmukle, Pitambar Gadhave

Author: Sahil Sunil Gharat

Paper ID: V5I3-1671

Paper Status: published

Published: May 30, 2019

Full Details
Research Paper

Vibration analysis and experimentation of centrifugal pump impeller

The impeller is a rotating component of a Centrifugal Pump. In the Pump application, excessive vibrations encountered would pose a damaging effect on the impeller. Most of the dynamic machinery problems result from the interaction between the exciting forces & associated structural frequencies. When frequency generated by exciting force becomes equal to natural frequency, the amplitude of vibration becomes maximum causing resonance Hence the main objective is to carry out static vibration analysis and conduct experimentation performance on the Impeller of two material- MS & Nylon and record the running pump parameters – Pressure head (H) & flow rate (Q) and deserve when the pump is running smoothly without any noise. The smooth run, without noise, indicates that the vibration level is normal. To find out the natural frequency of an impeller modal analysis was carried out. Cad model generation was done in CATIA V5, meshing in HYPER MESH and ANSYS is for post-processing. The experimentation carried out using different material (MS & Nylon) should not only smooth run of the Pump, but also improves the Pump efficiency resulting sufficient power saving of the pump.

Published by: Suraj Sudamji Wankhade, S. S. Jarikote

Author: Suraj Sudamji Wankhade

Paper ID: V5I3-1690

Paper Status: published

Published: May 30, 2019

Full Details
Thesis

Strengthening of reinforced concrete beam using glass fiber reinforced polymer

The maintenance, rehabilitation, and upgrading of structural members are perhaps one of the most crucial problems in civil engineering applications. Moreover, a large number of structures constructed in the past using the older design codes in different parts of the world are structurally unsafe according to the new design codes. Since replacement of such deficient elements of structures incurs a huge amount of public money and time, strengthening has become the acceptable way of improving their load carrying capacity and extending their service lives. In the present study, an experimental investigation is carried out on the flexural and shear behavior of RC beams strengthened using continuous GFRP sheets are carried out. Externally reinforced concrete beams with epoxy-bonded GFRP sheets were tested to failure using a symmetrical two-point concentrated static loading system. Two sets of beams were cast for this experimental test program. In SET I three beams weak in flexure were cast, out of which one is controlled beam and other two beams were strengthened using continuous GFRP sheets in flexure. In SET II three beams weak in shear were cast, out of which one is the controlled beam and other two beams were strengthened using continuous GFRP sheets in shear. The strengthening of the beams is done with the varying configuration of GFRP sheets.

Published by: Rupesh Khatri, Dr. G. P. Khare, Dushyant Kumar Sahu

Author: Rupesh Khatri

Paper ID: V5I3-1686

Paper Status: published

Published: May 30, 2019

Full Details
Research Paper

Experimental study on material of compound parabolic concentrator to increase efficiency of solar evacuated tube for hard water desalination

The use of solar energy in thermal desalination process is one of the most promising applications of renewable energies. In a solar desalination system, solar energy is utilized for heating salt water and converting it into soft water. A set of the evacuated tube and compound parabolic solar collector mainly get high-temperature performance in the range of 1200˚C-1250˚C. The annual yield is at its maximum when the condensing glass cover inclination is equal to the latitude of the place. The solar desalination system is eco-friendly and popular in rural areas. In the future, there is great scope in research carried out with other developed technologies such as ETC, ETC with heat pipes and multistage solar distillation.

Published by: Sonali Hase, Shraddha Adewar, Divya Mane, Madhura Mahajan, Punam Kadam

Author: Sonali Hase

Paper ID: V5I3-1683

Paper Status: published

Published: May 30, 2019

Full Details
Research Paper

Advance health monitoring system using IoT

Health monitoring and help the patient in the emergency condition is the main objective of this project. The aim of the project is to early inform the abnormal conditions of the body to the doctor and patient. The project mainly based on embedded system and IOT. The proposed system consists of hardware such as controller, temperature sensor, heartbeat sensor, load cell, ultrasonic sensor, LED, Wi-Fi module and LCD. In this project, the different sensor measure the body parameters such as body temperature, heartbeats, weight, height, and the readings are sent to the IoT server over wireless communication (Wi-Fi). If there are any abnormalities in measurement doctor will get alert about them. We can use this project on a daily basis to monitor body condition and help to doctor for monitoring patient remotely.

Published by: Sachin Ramdas Kalane, Akshay Dilip Patil, Mayuri Shashikant Jawade, Dr. K. M. Gaikwad

Author: Sachin Ramdas Kalane

Paper ID: V5I3-1659

Paper Status: published

Published: May 30, 2019

Full Details
Request a Call
If someone in your research area is available then we will connect you both or our counsellor will get in touch with you.

    [honeypot honeypot-378]

    X
    Journal's Support Form
    For any query, please fill up the short form below. Try to explain your query in detail so that our counsellor can guide you. All fields are mandatory.

      X
       Enquiry Form
      Contact Board Member

        Member Name

        [honeypot honeypot-527]

        X
        Contact Editorial Board

          X

            [honeypot honeypot-310]

            X